Bio bidet 200 installation

	Introducing Cleanrite, Distributors of Quality Bathroom Personal Care Products Offering Quality Constructed Attachments Which Transform Any Toilet or Commode into a Bidet!

[bidet-links.htm]

BIO Bidet

BB-I3000 Installation | BB-1000 Installation
BB-500 Installation | BB-300H Installation
BB-200 Installation | BB-50 Installation

bidet,bathroom accessories, bathroom, fixtures, plumbing supplies, toilet

BB-200
WARM WATER BIDET
Available in White

( Retail Price $249.00) $129.95 each

Useful Information

- Warranty Information

- Installation Instruction

- Control Panel

Don't have
Acrobat Reader?

Click here

to download

Installation Instruction

What you have


Flexible Hoses 7/8"x3/8" 1/2"x3/8"	(2) Adapters with emergency shut valve	10' White tube	(3) Rubber seal	(2) 1/2" Converter

What you need


Teflon Tape	Screw Driver	Wrench	Cutter	Compression Fitting	Velcro Tape (optional)

First things first.

Locate hot water source and make sure supplied 10 feet of white tube is enough to connect both hot and cold water to BB-200.
Should you need extra length of tube, contact customer service or distributor in you area for immediate supply. Compression fitting is not standard supply. Be sure to have it before cutting pipe.

Installation

	1. Shut off the water valve. 2. Measure and cut copper pipe using cutter. 3. Unscrew and detach bolt. 4. Apply bolt first, then slide compression fitting. 5. Slide down and fit it to top thread of adapter. (copper pipe must be straight to thread) 6. Insert packing into bottom of adapter as illustrated, then tighten adapter to main water valve. Avoid having tube inlet addressed directly to top of water valve to turn it back on freely. You can now close emergency shut off valve and turn on main water valve to test if there is any leak.
	Insert one end of the white tube into adapter inlet with nut as shown, the insert the other end to BB-200 hot water inlet. Use Velcro tape to secure white tube to edge of wall. This will prevent accidental unplugging tube and tube from hanging.
	If you have a flexible metal hoes instead of copper pipe, simply substitute it with supplied flexible hose with packing inserted. For cold water connection, please refer to BB-50 installation page.

Ready? Go!
	Trying your Bio-Bidet for the first time. Congratulations! Your are ready to use the Bio-Bidet for the first time. IT IS VERY IMPORTANT THAT YOU USE "NOZZLE CLEANING" EVERY TIME YOU USE BB-200. IT WILL: 1. PREVENT ACCIDENTAL NOZZLE CLOGGING. 2. PREVENT TOILET CLOGGING. 3. IT WILL BRING UP ENOUGH HOT WATER TO PROVIDE YOU WARM WATER WHEN YOU ARE READY TO CLEAN YOURSELF. To use it, simply pull it up all the way residual cold water is drained and warm water starts to run through. You must push it down before adjusting water pressure.

Using 1/2" Converter
	If your main water line has 1/2" male thread instead of 3/8", simply convert it to 3/8" using supplied converter. Simply insert converter in between main water line hose as illustrated. have further questions or need assistance? Contact any of our distributors in you area or a representative at our main office. We are there to help with your questions.

Trouble Shooting
	If your spray nozzle is clogged, you can remove the spray outlet by turning it 90 degree counter clockwise and pulling it down. After cleaning it, put it back an turn 90 degree clockwise to lock. You can select two different water spray angles by pulling the spray outlet tip up or pushing it back as illustrated.

FINAL ASSEMBLED FIGURE.

Have a friend who might be interested? Inform them about us now!

Cleanrite.com

Your Email Address

Your Name

Friend's Email

Friend's Name

Have questions about our bidet products?
Give us a call at our number (877) 852-2823 (702) 951-7256

Flexible Hoses 7/8"x3/8" 1/2"x3/8"

(2) Adapters with emergency shut valve

10' White tube

(3) Rubber seal

(2) 1/2" Converter

Teflon Tape

Screw Driver

Wrench

Cutter

Compression Fitting

Velcro Tape (optional)

1. Shut off the water valve.

2. Measure and cut copper pipe using cutter.

3. Unscrew and detach bolt.

4. Apply bolt first, then slide compression fitting.

5. Slide down and fit it to top thread of adapter. (copper pipe must be straight to thread)

6. Insert packing into bottom of adapter as illustrated, then tighten adapter to main water valve.

Avoid having tube inlet addressed directly to top of water valve to turn it back on freely. You can now close emergency shut off valve and turn on main water valve to test if there is any leak.

Insert one end of the white tube into adapter inlet with nut as shown, the insert the other end to BB-200 hot water inlet.

Use Velcro tape to secure white tube to edge of wall. This will prevent accidental unplugging tube and tube from hanging.

If you have a flexible metal hoes instead of copper pipe, simply substitute it with supplied flexible hose with packing inserted.

For cold water connection, please refer to BB-50 installation page.

Trying your Bio-Bidet for the first time.

You must push it down before adjusting water pressure.

If your main water line has 1/2" male thread instead of 3/8", simply convert it to 3/8" using supplied converter.

Simply insert converter in between main water line hose as illustrated.

have further questions or need assistance? Contact any of our distributors in you area or a representative at our main office.

We are there to help with your questions.

FINAL ASSEMBLED FIGURE.

Flexible Hoses
7/8"x3/8"
1/2"x3/8"

(2) Adapters with
emergency shut valve

Velcro Tape
(optional)

5. Slide down and fit it to top thread of adapter.
(copper pipe must be straight to thread)

6. Insert packing into bottom of adapter as illustrated,
then tighten adapter to main water valve.

Avoid having tube inlet addressed directly to top of water valve to turn it back on freely.
You can now close emergency shut off valve and turn on main water valve to
test if there is any leak.

Insert one end of the white tube into adapter inlet with nut as shown, the
insert the other end to BB-200 hot water inlet.

Use Velcro tape to secure white tube to edge of wall.
This will prevent accidental unplugging tube and tube from hanging.

If you have a flexible metal hoes instead of copper pipe,
simply substitute it with supplied flexible hose with packing inserted.

If your main water line has 1/2" male thread instead of 3/8", simply convert it to 3/8"
using supplied converter.

have further questions or need assistance?
Contact any of our distributors in you area or a representative at our main office.